5/13/2013

555 Pulse Generator

Description:
A 555 pulse generator circuit with a difference, the initial pulse is tailored by additional circuitry to match the duration of subsequent pulses.
Notes:
The NE555 and the First Pulse
The first positive pulse from a classic 555-based oscillator is always 1.6 times longer than the following pulses. The difference is caused by the fact that only during the first cycle C2 starts charging up from 0 V. This is generally not a problem, but sometimes this first pulse just should be the same length as the rest - at least approximately.
The picture shows the oscillator and an addition to it (everything to the right from the Vs-Gnd axis) that can solve the problem. Immediately after switch-on, C2 is empty and the voltage on the gate of Q2 is low. Q2 is off and it makes C2 charge up very quickly through Q1 and R3 until it reaches just below Vs/3. Then Q2 turns on, Q1 turns off, and the classic circuit continues to charge and discharge C2 relatively slowly between 2Vs/3 and Vs/3. As the voltage on C2 never again drops below Vs/3, Q2 now conducts all the time and Q1 is permanently off.
A MOSFET with a lower D-S resistance would charge up C2 even quicker.
The component values may be critical. For best results, the R5/R7 voltage divider should turn Q2 on when C2 is charged up to just a little below Vs/3. This point is set by the R5/R7 ratio. But if the value of R5 is too high or if R7 is too small (depending on the supply voltage and the G-S threshold voltage of Q2), the oscillator may not work at all. The sum of R5 and R7 should be as high as possible in order to minimize the influence on the main part of the circuit after the first pulse.

Hot Electronic Components & IC

ICL7107 CD4017 2N3055 LM3914 IRF3205 PT4115 2N2222A

5/09/2013

Solar Minty, DHT22 , Waterproof DS18B20 , PH Probe


This is a work in progress project which uses a Solar charging MintyBoost to power an Arduino with a Proto Screw Shield on it. Attached is a 2X16 LCD using the I2C Backpack, a DHT22 Temperature and Humidity Sensor, a Waterproof DS18B20 Sensor and a 5V analog PH Probe/Adapter.




PT4115 continuous conduction mode inductive step-down converter



The PT4115 is a continuous conduction mode inductive step-down converter, designed for driving single or multiple series connected LED efficiently from a voltage source higher than the total LED chain voltage. The PT4115 operates from an input supply between 6V and 30V and provides an externally adjustable output current of up to 1.2A. Depending upon the supply voltage and external components, the PT4115 can provide more than 30 watts of output power. The applications of the PT4115 include Low voltage halogen replacement LEDs, Automotive lighting, Low voltage industrial lighting, LED back-up lighting, Illuminated signs, SELV lighting, LCD TV backlighting.

5/08/2013

50 watt Power Amp OTL by LM3900, 2N3055




This be power amp OTL 50Watt use IC LM3900 and 2N3055 x 3pcs transistors to pillar equipment. Follow very circuit keeps to are Class ab then have a voice good loud. When , be amp OTL you then are certain that build easy use power supply the group is one 70V sizes by must use Current low 2Amp go up. Then have a voice good another thing you will like that amplifier. This durability do not make a loudspeaker a lose easy.





LM3914          IRF3205           PT4115          2N2222A            NRF24L01




Digital voltmeter using ICL7107

The circuit given here is of a very useful and accurate digital voltmeter with LED display using the ICL7107 from Intersil. The ICL7107 is a high performance, low power, 3.5 digit analog to digital converter. The IC includes internal circuitry for seven segment decoders, display drivers, reference voltage source and a clock. The power dissipation is less than 10mW and the display stability is very high.




The working of this electronic circuit is very simple. The voltage to be measured is converted into a digital equivalent by the ADC inside the IC and then this digital equivalent is decoded to the seven segment format and then displayed. The ADC used in ICL7107 is dual slope type ADC. The process taking place inside our ADC can be stated as follows. For a fixed period of time the voltage to be measured is integrated to obtain a ramp at the output of the integrator. Then a known reference voltage of opposite polarity is applied to the input of the integrator and allowed to ramp until the output of integrator becomes zero. The time taken for the negative slope to reach zero is measured in terms of the IC’s clock cycle and it will be proportional to the voltage under measurement. In simple words, the input voltage is compared to an internal reference voltage and the result is converted in a digital format.

The resistor R2 and C1 are used to set the frequency of IC’s internal clock. Capacitor C2 neutralizes the fluctuations in the internal reference voltage and increases the stability of the display.R4 controls the range of the voltmeter. Right most three displays are connected so that they can display all digits. The left most display is so connected that it can display only “1” and “-“.The pin5(representing the dot) is connected to ground only for the third display and its position needs to be changed when you change the range of the volt meter by altering R4. (R4=1.2K gives 0-20V range, R4=12K gives 0-200V range ).
Circuit diagram.

Notes.

    Assemble the circuit on a good quality PCB.
    The circuit can be powered from a +/_5V dual supply.
    For calibration, power up the circuit and short the input terminals. Then adjust R6 so that the display reads 0V.
    The ICL7107 is a CMOS device and it is very sensitive to static electricity. So avoid touching the IC pins with your bare hands.
    The seven segment displays must by common anode type.
    I assembled this circuit few years back and it is still working fine.



5/07/2013

EPC2LC20 Configuration Device


The EPC2LC20 is a Configuration Device which is designed for SRAM-Based LUT Devices.

EPC2LC20 absolute maximum ratings: (1)Supply voltage: -0.2 to 7.0 V With respect to ground; (2)DC input voltage: -0.2 to 7.0 V With respect to ground; (3)DC VCC or ground current: 50 mA; (4)DC output current, per pin: -25 to 25 mA; (5)Power dissipation: 250 mW; (6)Storage temperature: -65 to 150℃; (7)Ambient temperature: -65 to 135℃; (8)Junction temperature: 135℃.

EPC2LC20 features: (1)Serial device family for configuring APEXTM II, APEX 20K (including APEX 20K, APEX 20KC, and APEX 20KE), MercuryTM, ACEXR 1K, and FLEXR (FLEX 6000, FLEX 10KE, and FLEX 10KA) devices; (2)Easy-to-use 4-pin interface to APEX II, APEX 20K, Mercury, ACEX, and FLEX devices; (3)Low current during configuration and near-zero standby current; (4)5.0-V and 3.3-V operation; (5)Software design support with the AlteraR QuartusR II and; (6)MAX+PLUSR II development systems for Windows-based PCs as well as Sun SPARCstation, and HP 9000 Series 700/800.

5/06/2013

AD603AR low noise, voltage-controlled amplifier


The AD603AR is a low noise, voltage-controlled amplifier for use in RF and IF AGC systems. The AD603AR provides accurate, pin selectable gains of –11 dB to +31 dB with a bandwidth of 90 MHz or +9 dB to +51 dB with a bandwidth of 9 MHz. Any intermediate gain range may be arranged using one external resistor. The input referred noise spectral density is only 1.3 nV/ÖHz and power consumption is 125 mW at the recommended ±5 V supplies. The applications of the AD603AR include RF/IF AGC Amplifier, Video Gain Control, A/D Range Extension, Signal Measurement.

AD603AR absolute maximum ratings: (1)Supply Voltage ±VS: ±7.5 V; (2)Internal Voltage VINP (Pin 3): ±2 V Continuous, ±VS for 10 ms, GPOS, GNEG (Pins 1, 2): ±VS; (3)Internal Power Dissipation: 400 mW; (4)Operating Temperature Range: –40℃ to +85℃; (5)Storage Temperature Range: –65℃ to +150℃; (6)Lead Temperature Range (Soldering 60 sec): +300℃.

AD603AR features: (1)"Linear in dB" Gain Control; (2)Pin Programmable Gain Ranges: -1 dB to +31 dB with 90 MHz Bandwidth, +9 dB to +51 dB with 9 MHz Bandwidth; (3)Any Intermediate Range, e.g., -1 dB to +41 dB with 30 MHz Bandwidth; (4)Bandwidth Independent of Variable Gain; (5)1.3 nV√Hz Input Noise Spectral Density; (6)±0.5 dB Typical Gain Accuracy; (7)MIL-STD-883 Compliant and DESC Versions Available.

5/01/2013

Measuring and Test Circuit 2N7002


                                    2N7002

Constant off-time switching regulators offer several advantages over constant-frequency designs The only potential problem is that the switching frequency Increases with nsmg input voltage In designs that have large ratios of the high line to low-line supply voltage,this frequency shift can get quite large As a result,the switching losses can become excesslve at high input voltages To offset this problem,the simple circuit shown detects the high input voltage condition and lowers the switching frequency to keep switching losses under control The frequency-shift circuit consists of D3,R8,Q1,and C12 When Vin exceeds the zener voltage plus the FET threshold,Q1 turns on and adds an extra timing capacitor(C12) in parallel with the timing capacitor (C10) This increases the off-time,lowering the frequency.